THIS SPECIFICATION IS THE PROPERTY OF BOE HYDISAND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE HYDIS AND MUST BE RETURNED TO BOE HYDIS UPON ITS REQUEST.
PROPRIETARY NOTE
TITLE: HT12X13-100 Product Specification
Rev. E
FOR MORE INFORMATION:
AZ DISPLAYS, INC. 75 COLUMBIA, ALISO VIEJO, CA, 92656 Http://www.AZDISPLAYS.com
BOE HYDIS TECHNOLOGY
SPEC. NUMBER S864-1189 B2005-C001-A (1/3)
PRODUCT GROUP TFT-LCD PRODUCT
REV. E
ISSUE DATE 2006.02.23
PAGE 1 OF 23 A4 (210 X 297)
PRODUCT GROUP TFT-LCD PRODUCT
REV. E
ISSUE DATE 2006.02.23
REVISION HISTORY
REV.
O A
ECN NO.
DESCRIPTION OF CHANGES
DATE
04.05.31 04.07.09
PREPARED
S.M.Lee H.R.Park
B
C
D
E
Initial Release Lamp Start Voltage Change. (7 Page) -. Typ. Data (860, 1080) Delete. E407-F009 -. Max. Data -> Min. Data Change. -. Note 4 Add. Power Supply Current Change. (7 Page) E408-F020 -. Typ. Current : 233 -> 255 -. Max. Current : 430 -> 455 Power Supply Current Change. (7 Page) -. Max. Current : 455 -> 475 E0504-F016 Specify Max current pattern -. b) Max : V2 skip pattern -> V2 skip pattern (L28) General Description (4page) E0601-F005 -. Information about RoHS product Label modification ( 20page) Power Supply Current Change. (7 Page) E0602-F018 -. Typ. Current : 255 -> 300 -. Max. Current : 455 -> 500
04.08.31
I.H.JUN
05.05.03
H.K.KIM
06.01.06
M.S.Ha
06.02.23
S.M.LEE
SPEC. NUMBER S864-1189 B2005-C001-A (2/3)
SPEC. TITLE HT12X13-100 Product Specification
PAGE 2 OF 23 A4 (210 X 297)
PRODUCT GROUP TFT-LCD PRODUCT
REV. E
ISSUE DATE 2006.02.23
Contents
No 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 General Description Absolute Maximum Ratings Electrical Specifications Optical Specifications Interface Connection Signal Timing Specifications Signal Timing Waveforms of interface signal (DE mode) Input Signals, Display Colors & Gray Scale of Colors Power Sequence Mechanical Characteristics Reliability Test Handling & Cautions Environment & Safety Appendix Item Page 4 6 7 8 10 12 14 15 16 17 18 19 20 21
SPEC. NUMBER S864-1189 B2005-C001-A (3/3)
SPEC. TITLE HT12X13-100 Product Specification
PAGE 3 OF 23 A4 (210 X 297)
PRODUCT GROUP TFT-LCD PRODUCT
1.0 GENERAL DESCRIPTION 1.1 Introduction
REV. E
ISSUE DATE 2006.02.23
HT12X13-100 is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 12.1 inch diagonally measured active area with XGA resolutions (1024 horizontal by 768 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 262,144 colors. The TFT-LCD panel used for this module is a low reflection and higher color type.
CN1
VDD (3.3V)
Power Block
Source Driver IC (COF)
T/CON LVDS 1CH (6bit) Gate Driver IC (COF)
12.1" XGA
CN2
Lamp Reflector Lamp
1.2 Features Thin and light weight 3.3 V power supply Low driving voltage and low power consumption 1 Channel LVDS Interface Single CCFL (Bottom side/Horizontal Direction) 262,144 colors Data enable signal mode Side Mounting Frame RoHS product
SPEC. NUMBER S864-1189 B2005-C001-A (3/3)
SPEC. TITLE HT12X13-100 Product Specification
PAGE 4 OF 23 A4 (210 X 297)
PRODUCT GROUP TFT-LCD PRODUCT
1.3 Applications Notebook PC
REV. E
ISSUE DATE 2006.02.23
1.4 General Specifications
Parameter Active area Number of pixels Pixel pitch Pixel arrangement Display colors Display mode Dimensional outline Weight Back-light 1024 (H) x768 (V)
Specification 245.76 (H) x184.32 (V) 0.240 (H) x0.240 (V) RGB Vertical stripe 262,144 Normally white 261.00.5(W) x199.00.5(V) x4.7(D) Typ./5.0(D)Max 290 (Typ.) / 300 (Max.) CCFL, Horizontal-lamp type
Unit mm pixels mm colors mm g
Remarks
Note 1
Note 1: CCFL (Cold Cathode Fluorescent Lamp)
SPEC. NUMBER S864-1189 B2005-C001-A (3/3)
SPEC. TITLE HT12X13-100 Product Specification
PAGE 5 OF 23 A4 (210 X 297)
PRODUCT GROUP TFT-LCD PRODUCT
REV. E
ISSUE DATE 2006.02.23
2.0 ABSOLUTE MAXIMUM RATINGS The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit.
< Table 2. Absolute Maximum Ratings> Parameter Logic Power Supply Logic Input Voltage Back-light Lamp Current Back-light Frequency Operating Temperature Storage Temperature Symbol VDD VIN IBL FBL TOP TSP Min. VSS-0.3 VSS-0.3 2.0 45 0 -20 Max. 4.0 VDD+0.3 6.0 80 +50 +60 Unit V V mA KHz Note 1 Remarks Ta = 25 2
Note 1. Temperature and relative humidity range are shown in the figure below. * 90 [%] RH Max. (40 Ta) * Maximum wet-bulb temperature at 39 or less.(Ta40) No condensation
100 90 80
(40,90)
Relative Humidity (%RH)
60
(50,50)
Ope r a tin g R a n ge
40
(60,30)
20
S tor a ge R a n ge
5 -20 0 20 40 60 80
T e mpe r a tu r e (C)
SPEC. NUMBER S864-1189 B2005-C001-A (3/3)
SPEC. TITLE HT12X13-100 Product Specification
PAGE 6 OF 23 A4 (210 X 297)
PRODUCT GROUP TFT-LCD PRODUCT
3.0 ELECTRICAL SPECIFICATIONS
REV. E
ISSUE DATE 2006.02.23
[Ta = 252]
Parameter
Min. VDD IDD VIH VIL VBL IBL FL -100 690 2.0 45 1,080 1,350 3.0
Typ. 3.3 300 600 5.0
Max. 3.6 500 +100
Unit V mA mV mV
Remarks Note1 Note1
Power Supply Voltage Power Supply Current High Level Differential Input Signal Voltage Low Level Differential Input Signal Voltage Back-light Lamp Voltage Back-light Lamp Current Back-light Frequency Lamp operating
570 6.0 80
Vrms
Note2
mA KHz
Vrms Vrms One Lamp, Note3
At Ta=25, Note4 At Ta=0, Note4
Lamp Start Voltage Lamp Life Power Consumption
PD PBL Ptotal
10,000
15,000 1.0 3.0 4.0 1.65 3.3 4.95
Hrs W W W
IBL= 6mA, Note5 Typ.@8color bar IBL=5mA, Note6
Notes : 1. The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for 3.3V at 25. a) Typ: 8 color bar Pattern b) Max: V2 skip Pattern (L28) 2. Reference value, which is measured with Samsung Electric SIC-180 Inverter. (VBL Min is value at IBL Min and VBL Max is value at IBL Max) 3. The lamp frequency should be selected as different as possible from the horizontal synchronous frequency and its harmonics to avoid interference which may cause line flow on the display. 4. For starting the backlight unit, the output voltage of DC/AC's transformer should be larger than the minimum lamp starting voltage.(1,080 Vrms at 25 & 1,350 Vrms at 0 ) If an inverter has shutdown function it should keep its output for more than 1 second even if the lamp connector open. Otherwise the lamps may not to be turned on. 5. End of Life shall be determined by the time when any of the following is satisfied under continuous lighting at 25 and IBL = 6.0[mA]. Intensity drops to 50% of the Initial Value. 6. Calculated value for reference (VBL x IBL)
SPEC. NUMBER S864-1189 B2005-C001-A (3/3)
SPEC. TITLE HT12X13-100 Product Specification
PAGE 7 OF 23 A4 (210 X 297)
PRODUCT GROUP TFT-LCD PRODUCT
4.0 OPTICAL SPECIFICATIONS 4.1 Overview
REV. E
ISSUE DATE 2006.02.23
The test of Optical specifications shall be measured in a dark room (ambient luminance 1 lux and temperature = 252) with the equipment of Luminance meter system (Goniometer system and TOPCONE BM-5) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of and equal to 0. We refer to O=0 (=3 ) as the 3 o'clock direction (the "right"), O=90 (= 12 ) as the 12 o'clock direction ("upward"), O=180 (= 9 ) as the 9 o'clock direction ("left") and O=270(= 6 ) as the 6 o'clock direction ("bottom"). While scanning and/or O, the center of the measuring spot on the Display surface shall stay fixed. The backlight should be operating for 30 minutes prior to measurement... VDD shall be 3.3+/- 0.3V at 25C. Optimum viewing angle direction is 6 o'clock. 4.2 Optical Specifications
Symbol 3 Viewing Horizontal 9 Angle 12 range Vertical 6 Luminance Contrast ratio CR Luminance 5 Points Yw of White White 5 Points Y5 Luminance uniformity 13 Points Y13 xw White Chromaticity yw Red xR yR Reproduction Green xG of color yG Blue xB yB Response Rise Tr Time Td Decay Cross Talk CT
Parameter
Condition CR > 10 = 0 = 0 IBL = 5mA = 0
Min.
40 40 15 45
Typ.
45 45 20 50
300
Max.
Unit Remark Deg. Deg. Note 1 Deg. Deg. Note 2 cd/m2 %
Note 3
130
150 85 75 0.315 0.332 0.581 0.337 0.309 0.544 0.150 0.143 10 20
= 0
80 65 0.285 0.302 0.551 0.307 0.279 0.514 0.120 0.113
Note 4 Note 5
Ta= 25 C = 0 = 0
0.345 0.362 0.611 0.367 0.339 0.574 0.180 0.173 20 40 2.0
ms ms %
Note 6 Note 7
SPEC. NUMBER S864-1189 B2005-C001-A (3/3)
SPEC. TITLE HT12X13-100 Product Specification
PAGE 8 OF 23 A4 (210 X 297)
PRODUCT GROUP TFT-LCD PRODUCT
Note:
REV. E
ISSUE DATE 2006.02.23
1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o'clock direction and the vertical or 6, 12 o'clock direction with respect to the optical axis which is normal to the LCD surface (see FIGURE 1 shown in Appendix). 2. Contrast measurements shall be made at viewing angle of = 0 and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See FIGURE 1 shown in Appendix) Luminance Contrast Ratio (CR) is defined mathematically.
CR =
Luminance when displaying a white raster Luminance when displaying a black raster
3. Average Luminance of white is defined as arithmetic mean of five measurement points across the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations shown in FIGURE 2 for a total of the measurements per display. 4. The White luminance uniformity on LCD surface is then expressed as : Y = Minimum Luminance of 5(or 13) points / Maximum Luminance of 5(or 13) points (see FIGURE 2 shown in Appendix). 5. The color chromaticity coordinates specified in Table 4 shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. 6. The electro-optical response time measurements shall be made as FIGURE 3 shown in Appendix by switching the "data" input signal ON and OFF. The times needed for the luminance to change from 10% to 90% is Tr, and 90% to 10% is Td. 7. Cross-Talk of one area of the LCD surface by another shall be measured by comparing the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (YB) of that same area when any adjacent area is driven dark. (See FIGURE 4 shown in Appendix).
SPEC. NUMBER S864-1189 B2005-C001-A (3/3)
SPEC. TITLE HT12X13-100 Product Specification
PAGE 9 OF 23 A4 (210 X 297)
PRODUCT GROUP TFT-LCD PRODUCT
5.0 INTERFACE CONNECTION
REV. E
ISSUE DATE 2006.02.23
5.1 Electrical Interface CN1 Interface connector User side connector Pin No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Symbol VDD1 VDD2 VSS VSS RIN0RIN0+ VSS RIN1RIN1+ VSS RIN2RIN2+ VSS RCLKINRCLKIN+ VSS
Vdd_EDID NC Clk_EDID Clk_Data
: Hirose/DF19KR-20P-1H or equivalent : Hirose/DF19G-20S-1C or equivalent Function Power Supply: +3.3V Power Supply: +3.3V Ground Ground LVDS Negative data signal (-) LVDS Positive data signal (+) Ground LVDS Negative data signal (-) LVDS Positive data signal (+) Ground LVDS Negative data signal (-) LVDS Positive data signal (+) Ground LVDS Negative clock signal (-) LVDS Positive clock signal (+) Ground No Connection No Connection No Connection No Connection Tx pin # 40 Tx pin # 39 Tx pin # 42 Tx pin # 41 Tx pin # 46 Tx pin # 45 Tx pin # 48 Tx pin # 47 Remark
SPEC. NUMBER S864-1189 B2005-C001-A (3/3)
SPEC. TITLE HT12X13-100 Product Specification
PAGE 10 OF 23 A4 (210 X 297)
PRODUCT GROUP TFT-LCD PRODUCT
5.2 Back-light Interface CN2 Interface Connector Pin No 1 2 INPUT HOT COLD
REV. E
ISSUE DATE 2006.02.23
: BHSR-02VS-1 (JST) or equivalent Function High voltage Ground Remarks Pink Black
5.3 LVDS Interface LVDS Transmitter: THC63LVDM83A or equivalent. Input signal R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5 HSYNC VSYNC DE MCLK Transmitter Pin No 51 52 54 55 56 3 4 6 7 11 12 14 15 19 20 22 23 24 27 28 30 31 40 39 CLKOUTCLKOUT+ CLKINCLKIN+ 14 15 42 41 OUT2OUT2+ IN2IN2+ 11 12 46 45 OUT1OUT1+ IN1IN1+ 8 9 48 47 OUT0OUT0+ IN0IN0+ 5 6 Pin No Interface System (Tx) TFT-LCD (Rx) DF19KR-20P-1H Pin No. Remark
SPEC. NUMBER S864-1189 B2005-C001-A (3/3)
SPEC. TITLE HT12X13-100 Product Specification
PAGE 11 OF 23 A4 (210 X 297)
PRODUCT GROUP TFT-LCD PRODUCT
5.4 Data Input Format (1,1) (2,1) RGBRGB
REV. E
ISSUE DATE 2006.02.23
(1023,1) (1024,1) RGBRGB
1 Pixel = 3 Dots
RGB
RGBRGB (1,768) (2,768)
RGBRGB (1023,768) (1024,768) Display position of input data
6.0 SIGNAL TIMING SPECIFICATIONS 6.1 The 12.1"XGA LCM is operated by the only DE (Data enable) mode (LVDS Transmitter Input) Item Symbols Min Typ Max Unit Frequency Clock High Time Low Time Setup Time Data Hold Time Data Enable Setup Time Frame Period Vertical Display Period One Line Scanning Period Horizontal Display Period 1/Tc Tch Tcl Tds Tdh Tes Tv Tvd Th Thd 4.5 4.5 2.7 0 2.7 772 768 1100 1024 65 806 768 1344 1024 80 1022 768 2046 1024 MHz ns ns ns ns ns lines lines clocks clocks
SPEC. NUMBER S864-1189 B2005-C001-A (3/3)
SPEC. TITLE HT12X13-100 Product Specification
PAGE 12 OF 23 A4 (210 X 297)
PRODUCT GROUP TFT-LCD PRODUCT
6.2 LVDS Rx interface timing parameter
REV. E
ISSUE DATE 2006.02.23
The specification of the LVDS Rx interface timing parameter Item Symbol Min Typ Max CLKIN Period tRCIP 12.5 15.38 Input Data 0 tRIP1 -0.4 0.0 +0.4 Input Data 1 tRIP0 1*tRICP/7 1*tRICP/7 1*tRICP/7 -0.4 +0.4 Input Data 2 tRIP6 2*tRICP/7 2*tRICP/7 2*tRICP/7 -0.4 +0.4 Input Data 3 tRIP5 3*tRICP/7 3*tRICP/7 3*tRICP/7 -0.4 +0.4 Input Data 4 tRIP4 4*tRICP/7 4*tRICP/7 4*tRICP/7 -0.4 +0.4 Input Data 5 tRIP3 5*tRICP/7 5*tRICP/7 5*tRICP/7 -0.4 +0.4 Input Data 6 tRIP2 6*tRICP/7 6*tRICP/7 6*tRICP/7 -0.4 +0.4
Unit nsec nsec nsec nsec nsec nsec nsec nsec
Remark
tRIP2 tRIP3 tRIP4 tRIP5 tRIP6 tRIP0 tRIP1 RINz +/RCLKIN+ * Z=0, 1, 2, 3
Rx3 Rx2 Rx1 Rx0 Rx6 Rx5 Rx4 Rx3 Rx2 Rx1 Rx0
Vdiff=0[v] tRCIP
Vdiff=0[v]
* Vdiff = (RINz+)-(RINz-), (RCLKIN+)-(RCLKIN-)
SPEC. NUMBER S864-1189 B2005-C001-A (3/3)
SPEC. TITLE HT12X13-100 Product Specification
PAGE 13 OF 23 A4 (210 X 297)
PRODUCT GROUP TFT-LCD PRODUCT
REV. E
ISSUE DATE 2006.02.23
7.0 SIGNAL TIMING WAVEFORMS OF INTERFACE SIGNAL (DE MODE) 7.1 Vertical Timing Waveforms
Tv Tvd
MCLK Th ENAB
R7 ~ R0 G7 ~ G0 B7 ~ B0
Invalid Data
x,1
x,2
x,y
x,768
Invalid
Data
x+1,1
7.2 Horizontal Timing Waveforms
Th Thd M CLK Tc EN A B
RA 7 ~RA 0 G A 7 ~G A 0 BA 7 ~BA 0
D1
D2
Dn
D1022
D 1023
D1024
Invalid
Data
D1
D2
D3
Tch M CLK T ds D a ta
Tcl 2.0V 1.5V T dh D a ta 2.0V 0.8V 0.8V
V a lid Tes
EN A B
2.0V
SPEC. NUMBER S864-1189 B2005-C001-A (3/3)
SPEC. TITLE HT12X13-100 Product Specification
PAGE 14 OF 23 A4 (210 X 297)
PRODUCT GROUP TFT-LCD PRODUCT
REV. E
ISSUE DATE 2006.02.23
8.0 INPUT SIGNALS, BASIC DISPLAY COLORS & GRAY SCALE OF COLORS
Colors & Gray Scale Black Blue Green Basic Cyan Colors Red Magenta Yellow White Black Darker Gray Scale Of Red Brighter Red Black Darker Gray Scale Of Green Brighter Green Black Darker Gray Scale Of Blue Brighter Blue Black Gray Darker Scale Of White & Brighter Black White Red Data
R5 R4 R3 R2 R1 R0 G5
Green Data 0 0 0 0 1 1 1 1 0 0 1 0 0 0 0 1 1 1 1 0 1 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0
Blue Data 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0
G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0
0 0 0 0 1 1 1 1 0 0 0
0 0 0 0 1 1 1 1 0 0 0
0 0 0 0 1 1 1 1 0 0 0
0 0 0 0 1 1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
0 1 1 0 0 0
1 0 1 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 1
0 0 0 0 1 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
0 1 1 0 0 0
1 0 1 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 1
0 0 0 0 1 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 1
0 0 0 0 1 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 1
0 0 0 0 1 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
0 1 1 0 0 1
1 0 1 0 1 0
1 1 1
1 1 1
1 1 1
1 1 1
0 1 1
1 0 1
1 1 1
1 1 1
1 1 1
1 1 1
0 1 1
1 0 1
1 1 1
1 1 1
1 1 1
1 1 1
0 1 1
1 0 1
SPEC. NUMBER S864-1189 B2005-C001-A (3/3)
SPEC. TITLE HT12X13-100 Product Specification
PAGE 15 OF 23 A4 (210 X 297)
PRODUCT GROUP TFT-LCD PRODUCT 9.0 POWER SEQUENCE
REV. E
ISSUE DATE 2006.02.23
To prevent a latch-up or DC operation of the LCD module, the power on/off sequence should be as shown in below
ON
ON
90% VDD 10% OFF
3.0V V2
t10 Logic Signal
t1 t2 t7
t3 t4 t5 t8
t6 t9
CCFL Power
0 < t1 0 < t2 0 t3 t7 t9
10 ms 50 ms 50 ms 100 ms
200ms
0 t4 50 ms 0 < t5 50 ms t6 10 ms t8 100 ms t10 10 ms
2.8 V V2 3.0V Notes : 1. When the power supply VDD is 0V, Keep the level of input signals on the low or keep high impedance. 2. Do not keep the interface signal high impedance when power is on. 3. Back Light must be turn on after power for logic and interface signal are valid.
SPEC. NUMBER S864-1189 B2005-C001-A (3/3)
SPEC. TITLE HT12X13-100 Product Specification
PAGE 16 OF 23 A4 (210 X 297)
PRODUCT GROUP TFT-LCD PRODUCT
10.0 MECHANICAL CHARACTERISTICS
REV. E
ISSUE DATE 2006.02.23
10.1 Dimensional Requirements FIGURE 5, 6 shown in appendix shows mechanical outlines for the model. Parameter Active area Number of pixels Pixel pitch Pixel arrangement Display colors Display mode Dimensional outline Weight Back-light 10.2 Mounting See FIGURE 5 shown in appendix 1024(H) x768(V) (1 pixel = R + G + B dots) 0.240(H) x0.240(V) RGB Vertical stripe 262,144 Normally white 261.00.5(W) x199.00.5(V) x4.7(D) Typ./5.0(D)Max. 290 (Typ.) / 300 (Max.) CCFL, Horizontal-lamp type mm gram colors mm Specification 245.76 (H) x184.32 (V) Unit mm pixels
10.3 Anti-Glare and Polarizer Hardness. The surface of the LCD has an anti-glare coating to minimize reflection and a coating to reduce scratching.
10.4 Light Leakage There shall not be visible light from the back-lighting system around the edges of the screen as seen from a distance 50 cm from the screen with an overhead light level of 150lux. The manufacture shall furnish limit samples of the panel showing the light leakage acceptable.
SPEC. NUMBER S864-1189 B2005-C001-A (3/3)
SPEC. TITLE HT12X13-100 Product Specification
PAGE 17 OF 23 A4 (210 X 297)
PRODUCT GROUP TFT-LCD PRODUCT
11.0 RELIABILITY TEST
REV. E
ISSUE DATE 2006.02.23
No 1 2 3 4 5 6
Test Items High temperature storage test Low temperature storage test High temperature operation Test High temperature & high humidity operation test Low temperature operation test Thermal shock Vibration test Ta = 60 C, 240 hrs Ta = -20 C, 240 hrs Ta = 50 C, 240 hrs
Conditions
Ta = 50 C, 80 %RH, 240 hrs Ta = 0 C, 240 hrs Ta = -20 C 60 C (30 min), 100 cycle Frequency : 10 ~ 500 Hz : 1.5G : X, Y, Z 30 min : 220G : 2ms, half sine wave X, Y, Z Once for each direction Air : 150 pF, 330 , 15KV : 150 pF, 330 , 8KV
7 (non-operating)
Gravity/AMP Period Gravity Shock test
8 (non-operating)
Pulse width
9
Electrostatic discharge test Contact
SPEC. NUMBER S864-1189 B2005-C001-A (3/3)
SPEC. TITLE HT12X13-100 Product Specification
PAGE 18 OF 23 A4 (210 X 297)
PRODUCT GROUP TFT-LCD PRODUCT
12.0 HANDLING & CAUTIONS 12.1 Cautions when taking out the module Pick the pouch only, when taking out module from a shipping package.
REV. E
ISSUE DATE 2006.02.23
12.2 Cautions for handling the module As the electrostatic discharges may break the LCD module, handle the LCD module with care. Peel a protection sheet off from the LCD panel surface as slowly as possible. As the LCD panel and backlight element are made from fragile glass material, impulse and pressure to the LCD module should be avoided. As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning. Do not pull the interface connector in or out while the LCD module is operating. Put the module display side down on a flat horizontal plane. Handle connectors and cables with care. 12.3 Cautions for the operation When the module is operating, do not lose MCLK, DE signals. If any one of these signals were lost, the LCD panel would be damaged. Obey the supply voltage sequence. If wrong sequence were applied, the module would be damaged. 12.4 Cautions for the atmosphere Dewdrop atmosphere should be avoided. Do not store and/or operate the LCD module in a high temperature and/or humidity atmosphere. Storage in an electro-conductive polymer-packing pouch and under relatively low temperature atmosphere is recommended. 12.5 Cautions for the module characteristics Do not apply fixed pattern data signal to the LCD module at product aging. Applying fixed pattern for a long time may cause image sticking. 12.6 Other cautions Do not disassemble and/or re-assemble LCD module. Do not re-adjust variable resistor or switch etc. When returning the module for repair or etc, please pack the module not to be broken. We recommend using the original shipping packages.
SPEC. NUMBER S864-1189 B2005-C001-A (3/3)
SPEC. TITLE HT12X13-100 Product Specification
PAGE 19 OF 23 A4 (210 X 297)
PRODUCT GROUP TFT-LCD PRODUCT
13.0 Environment & Safety 13.1 Mercury disposal & High voltage caution
REV. E
ISSUE DATE 2006.02.23
13.2 Product Label
HT12X13-100
XXXXXXXXXXXXXXXX X
* BOE Hydis Barcode
1 X X 2 X 3 X X 4 X 5 X X X X 6 X X X X X X 7 X
1. Control Number 2. Rank / Grade 3. Line Classification (BOE Hydis : H, LCM : L, BOE OT : A/B/C) 4. Year (2001 : 01, 2002 : 02, ...)
5. Month (1,2,3, ... , 9, X, Y, Z) 6. FG Code 7. Serial Number
SPEC. NUMBER S864-1189 B2005-C001-A (3/3)
SPEC. TITLE HT12X13-100 Product Specification
PAGE 20 OF 23 A4 (210 X 297)
PRODUCT GROUP TFT-LCD PRODUCT
14.0 APPENDIX
REV. E
ISSUE DATE 2006.02.23
Figure 1. Measurement Set Up
(L = 50cm )
Figure 2. Average Luminance Measurement Locations & Uniformity Measurement Locations
42
192
6
7
8
2
3
384
9
1
10
576
4
5
726 Lines
11
12
13
42
X
256 : Test Point
512
768
982
Pixels
SPEC. NUMBER S864-1189 B2005-C001-A (3/3)
SPEC. TITLE HT12X13-100 Product Specification
PAGE 21 OF 23 A4 (210 X 297)
PRODUCT GROUP TFT-LCD PRODUCT
REV. E
ISSUE DATE 2006.02.23
Figure 3. Response Time Testing
T F T O n (B lack )
T F T O ff(W h ite)
T F T O n (B lack )
Td
Tr
100% 90%
10% 0%
Figure 4. Cross Modulation Test Description
VIEW AREA 256, 192 256, 576
VIEW AREA 768, 192
768, 576 YB (896, 384)
YA (896, 384)
Cross-Talk =
YB - YA YA
x 100
Where: YA = Initial luminance of measured area (cd/m2) YB = Subsequent luminance of measured area (cd/m2) The location measured will be exactly the same in both patterns.
SPEC. NUMBER S864-1189 B2005-C001-A (3/3)
SPEC. TITLE HT12X13-100 Product Specification
PAGE 22 OF 23 A4 (210 X 297)
PRODUCT GROUP TFT-LCD PRODUCT
REV. E
ISSUE DATE 2006.02.23
Figure 5. TFT-LCD Module Outline Dimensions (Front view)
Figure 6. TFT-LCD Module Outline Dimensions (Rearview)
HT12X13-100
XXXXXXXXXXXXXXX
SPEC. NUMBER S864-1189 B2005-C001-A (3/3)
SPEC. TITLE HT12X13-100 Product Specification
PAGE 23 OF 23 A4 (210 X 297)
| |
Price & Availability of HT12X13-100
 |
|
|
|
|
|
All Rights Reserved ©
IC-ON-LINE 2003 - 2022 |
.
.
.
.
.
| |
We use cookies to deliver the best possible
web experience and assist with our advertising efforts. By continuing to use
this site, you consent to the use of cookies. For more information on
cookies, please take a look at our
Privacy Policy. |
X |
|
